Having trouble with the network path not found error on Windows 10? Read on for a quick solution.
Solutions to Network Path Not Found Errors
If you encounter a “Network Path Not Found” error on your Windows 10 system, there are several solutions you can try to resolve the issue.
1. Check network connectivity: Ensure that your network cables are securely connected and that your network interface controller is working properly. You can also try restarting your router or modem.
2. Disable antivirus software: Temporarily disable your antivirus software as it may be blocking the network connection. If the error disappears after disabling the antivirus, consider adding an exception for the affected program or changing your antivirus settings.
3. Reset TCP/IP stack: Open a command-line interface (CMD.exe) with administrator privileges and run the following commands in order:
– netsh winsock reset
– netsh int ip reset
– ipconfig /release
– ipconfig /renew
4. Check firewall settings: Ensure that your firewall is not blocking the network path. You can temporarily disable the firewall or add an exception for the affected program.
5. Verify network sharing settings: Make sure network sharing is enabled on your Windows 10 system. Go to the Control Panel, click on “Network and Sharing Center,” and verify that network discovery and file sharing are enabled.
6. Restart network services: Restart the “Server” and “Workstation” services on your Windows 10 system. Press the Windows key + R, type “services.msc,” and press Enter. Locate the “Server” and “Workstation” services, right-click on each, and select “Restart.”
Troubleshooting Network Security and Sharing
If you’re experiencing the “Network Path Not Found” error on Windows 10, here are some troubleshooting steps to help you fix it.
1. Check your network connection: Make sure your computer is connected to the network properly. Verify that your network cables are securely plugged in and your Wi-Fi is turned on.
2. Disable firewall: Temporarily disable your firewall to see if it’s causing the issue. Press the Windows key + R, type “control panel,” and hit Enter. Go to “System and Security” > “Windows Defender Firewall” > “Turn Windows Defender Firewall on or off.” Choose the option to turn it off for both private and public networks.
3. Restart network devices: Restart your modem, router, and any other network devices you have. Unplug them from the power source, wait for a few seconds, and then plug them back in.
4. Reset TCP/IP stack: Open a command prompt with administrative privileges by pressing the Windows key + X and selecting “Command Prompt (Admin).” Type the following commands one by one, pressing Enter after each:
– netsh winsock reset
– netsh int ip reset
5. Check network sharing settings: Right-click on the folder you’re trying to access and select “Properties.” Go to the “Sharing” tab and make sure the “Share this folder” option is checked. Also, check the permissions to ensure that the appropriate users or groups have access.
6. Verify network discovery settings: Press the Windows key + R, type “control panel,” and hit Enter. Go to “Network and Internet” > “Network and Sharing Center” > “Change advanced sharing settings.” Make sure network discovery is turned on.
7. Disable NetBIOS over TCP/IP: Open a command prompt with administrative privileges and type the following command, then press Enter:
– netsh interface ipv4 set netbios overtcpip disabled
Adjusting SMB Settings for File Sharing
|SMB Setting||Description||Recommended Value|
|Enable SMB||Enable or disable the SMB protocol for file sharing.||Enabled|
|SMB Version||Set the SMB version to be used for file sharing.||SMBv2 or higher|
|Network Discovery||Allow Windows to discover and connect to devices on the network.||Enabled|
|File and Printer Sharing||Enable sharing of files and printers on the network.||Enabled|
|Firewall Settings||Configure the firewall to allow SMB traffic.||Open ports 139 and 445|
By adjusting these SMB settings, you can resolve the “Network Path Not Found” error and ensure smooth file sharing on your Windows 10 computer.
Configuring Network Discovery and Credentials
To fix the “Network Path Not Found” error in Windows 10, you need to configure network discovery and credentials.
First, open the Control Panel by searching for it in the Start menu.
Next, click on “Network and Sharing Center” and then select “Change advanced sharing settings” from the left-hand menu.
In the Advanced Sharing Settings window, make sure that network discovery is turned on for your network profile.
To enable network discovery, check the box next to “Turn on network discovery” and click on “Save changes”.
Additionally, you may need to configure your credentials. Go back to the Control Panel and click on “Credential Manager”.
In the Credential Manager window, click on “Windows Credentials” and then “Add a Windows credential”.
Enter the network address and the username and password you want to use to access the network. Click on “OK” to save the credentials.
After configuring network discovery and credentials, you should be able to access the network without encountering the “Network Path Not Found” error.